Amp hook up to stock radio, yahoo answers

  • John, Processors like this get connected between a receiver and amplifier.
  • All finished with your chat session?
  • The Epicenter's outputs would then go to the subwoofer amplifier's inputs.
  • Or would my sub have to share the same full sound as the speakers are receiving?

Hi Buck, I want my system to sound richer with good syrupy sound. Rick, You won't need any line output converters if you use amplifiers with speaker-level inputs. Carl, Yes, you can connect that subwoofer to two bridged channels of that amp and that speaker to the other two channels bridged together.

As the typical subwoofer amplifier will be two or three times more powerful than the full-range amp in a system, that's where the greatest demand will occur, when the bass hits. Is this article up to date? Due to my idiocy resulting in blowing my previous fuse what size fuse do you recommend I install for this new audio setup? Is that supposed to work like that. Hello Buck, I have a question regarding relays.

It's not until you're installing three or four devices that you start needing a relay. Chris, If you had bought your gear at Crutchfield, you could call Tech Support for free help troubleshooting your system. Figure out where you're going to place the amp, put the beginning of your power red wire there and give it about a foot of wire extra, then begin to hide and run the power wire to under the hood. Buck, I have this similiar setup.

Yahoo Answers

This Lightning Audio L for example. Jake, Not only are there no problems doing this, here's an article explaining the technique. Once I install the new rear speakers, will I have to go back in and cut the speaker connection from the receiver to the factory harness? Good luck it will make a huge improvment. And can I run my power cables in parallel from the battery to each amp instead of using a power distribution block?

Report Abuse

Amp hook up to stock radio

Video of the Day

You should be aware that this large a system in any vehicle will be a challenge to power. If you do experience light-dimming along with the music, check out this article for help solving that. Don't forget to fuse each cable near the battery.

Adding subwoofer to stock car radio Polk Audio

They should be there for additional protection. Then run the remote wire back to the amp and cut it there leaving a foot or so of extra cable. Tomas, A distribution block isn't required in a multi-amp system, it just makes wiring easier and neater.

Is this the best way to hook it all up? What would happen if you hooked it up and the subs blew? Hook it to a fuse connected to ignition turn on, like your accessory power fuse.

How to hook up subs and amp to stock stereo in car

You can contact a Crutchfield Sales Advisor for recommendations via phone or chat. Just want to confirm what I am running is sufficient. Hi Buck, I have a question not related to this audio setup. How would i wire the tweeters into this circut? All products are possible, so the recommendations would still be appreciated.

And finally, am I going about this all wrong, should I be looking at an entirely different setup altogether? Each amp has its own inline fuse, coming out the distribution block. Then to each individual amplifier. My amp is already installed and I just bought a new sub. In this case, the patch cables that come from the receiver's subwoofer output would plug into the Epicenter's inputs.

Now for the Remote blue wire. Is there any information that you would be able to give me to help me out? And you could call Tech Support for free lifetime help with your system. You haven't explained what you want to accomplish. Do you have a diagram or advice on best way to do it?

Amplifier Wiring Diagrams How to Add an Amplifier to Your Car Audio System
How to Wire an Amp & Subwoofers Into a Stock Stereo

Anybody have any idea which wires I would need to tie in to? Ed, We at Crutchfield pride ourselves on helping our customers choose products and install them themselves. And if you have the room, hull daily mail dating you can definitely run two power cables from the battery to your two amplifiers. Connect the ground from the amplifier to the chassis. How should I connect the remote wire so that I don't have to disconnect it when I turn off the car?

Do you know if the stock speaker have connection for a Sub? For inside speakers, How and where do I intercept the stock wiring to be routed to the amp? My question is, do I need to upgrade my alternator or will the stock alternator be alright?

Would i need a y channel amp if thats even a thing? Dejuan, It depends on how you run the grounds from each amp. For instance, you mention Infinity tweeters and speakers. The current amplifier renegade ren has an output channel. Tell us about your vehicle.

Music is like candy, you have to get rid of the rappers to enjoy it. If it is even questionable, I would rather just run new cables to the doors. This article was written by the It Still Works team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information.

Is that too much for the factory small gauge wiring? You could experiment with high-pass settings for your tweeters and low-pass for the mid-bass drivers until it sounds good to you. My question, etrade speed dating commercial should i get A fuse or A fuse in line fuse holder near the battery?

Hook up amplifier to stock radio

  1. By submitting images, you agree to our terms and conditions.
  2. My pioneer has a front rear and sub ra connection spot.
  3. Free Shipping on All Orders!
  4. It will just plug into your truck and then connect color coordinated wires.
  5. Kris, I'm unfamiliar with that vehicle's trunk, so I can't help you with choosing a ground point.

Find what fits your vehicle. The fuse amperage should match the gauge size. Barry, Without knowing what vehicle you have, we can't help you with its speaker wiring. Or was this created from scratch in something like illustrator?

You could add additional subs to your system using these outputs. Then it goes from the amps to the speakers via speaker wires. Electrically, it'll be connected to all the amps in your system, but it will do the most good to the nearest amp. Seth, what is the The turn-on lead in the diagram is shown split like that for clarity. Amplifier wiring diagrams How to add an amplifier to your car audio system.

How to Wire an Amp to a Sub and Head Unit 12 Steps

Oh well, you can just pull the radio and tag the speakers there, single parent dating international you'll have to get an ignition source for the remote wire and its all behind the radio. What if I bought my radio harness to fit my truck only? How would i wire the speakers to my radio separate from my sub amp?

Adding subwoofer to stock car radio

Quick Links

Learn about Crutchfield Rewards. James, I can't hear your tweeters from here so I can't tell if the noise appears when no program is playing or only when something plays. Go to Corporate Sales page. Their toll-free number is on your invoice and you get free lifetime support for your products. And yes, you'll have to drill new speaker holes for them.

  • Dating site in vadodara
  • Kijiji dating
  • Ihk azubi speed dating düsseldorf 2019
  • 18 year old dating a 30 year old
  • Are brooke and brandon dating
  • 31 year old woman dating 26 year old man
  • Dating an old rich man
  • Comments on Amp hook up to stock radio, yahoo answers